Prestige LCD keyless remote car starter transmitter ELVATRBB APS596A AX700 AX900

Prestige LCD keyless remote car starter transmitter ELVATRBB APS596A AX700 AX900
Prestige LCD keyless remote car starter transmitter ELVATRBB APS596A AX700 AX900

Prestige LCD keyless remote car starter transmitter ELVATRBB APS596A AX700 AX900
Remote's case is worn and the graphics on the buttons of this remote will be faded. See pictures for an example of what you will receive. Remote keyless entry fob alarm controller. Transmitter control clicker keyfob controller replacement. See Item Specifications for more details.

Program Remote to Your Installed Aftermarket System. This remote needs to be programmed to your vehicle in order for it to work with your vehicles installed RKE (remote keyless entry) system.

Your Alarm and or Remote Start unit has a configurable receiver that allows the transmitter to be programmed to operate the Lock Unlock functions with one transmitter button or with two transmitter buttons (separate Lock/Unlock). In addition, the receiver also allows driver priority function. This driver priority function takes place whenever a particular transmitter is used to unlock the vehicle regardless of the selection of one button or two button operation.

The following indicates the receiver programmable slots. 3 Trunk Release & or Remote Start (Optional on some models). 6 Driver 1 Priority or Separate Output. 7 Driver 2 Priority or Separate Output. Receiver channels 6 or 7 will accept the programming of transmitter channel 1 if used as the Lock/Unlock button, or Channel 2 when separate Lock Unlock buttons are programmed. In this way, whenever the transmitter is used to unlock the vehicle, channel 6 or 7, when programmed, will provide a pulsed ground output.

This output can be connecter to the driver. Priority function of the vehicle to reset preset user features. Please consult with your installation centers technician to see if this feature is available in your vehicle.

NOTE: A total of 4 transmitters may be programmed into any receiver channel. Force programming a transmitter, removing a transmitter, or reprioritizing a transmitter is covered later in this manual. Also, if you do not program a transmitter button into channel 2 which is the separate unlock/disarm channel, then whatever button is programmed into channel 1 will serve as both lock/arm & unlock/disarm.

NOTE: The RED Button serves as a function button in combination with other buttons explained in your owners manual. This button may not be used to operate a receiver channel. NOTE: The Option Button is predetermined and programmed for access to Time Start, and Temperature Start & Check so it cannot be used for multiple button operation of any other feature. It will however operate for any single button programming. This transmitter is also capable of one button programming for certain model Audiovox Alarms.

If your alarm is one of these models, then when step 3 is completed on the following page, you can turn the ignition switch off and programming with the default button configurations for the first four channels will be complete. TO ENTER THE PROGRAM MODE. Turn the ignition switch to the ON position.

Within 10 seconds, Press and release the valet/program switch three times. (Siren emits 1 short chirp indicating channel 1 has been entered). Within 10 Seconds, Press and hold the button of the first transmitter you wish to control the Lock&Arm feature of your security system until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Lock/Arm feature). Within 10 seconds, press and release the valet program switch one time. (Siren emits 2 short chirps indicating channel 2 has been entered). Within 10 Seconds, Press and hold any unused button(s) of the first transmitter you wish to control the Unlock/Disarm feature of your security system until a long chirp is heard from the siren. NOTE: This channel is used only if you desire separate control of the Lock/Unlock feature.

If you wish to operate the Lock/Unlock features from a single button, move onto step 6 as whatever button is programmed into channel 1 will control both Lock & Arm/Unlock & Disarm. (Repeat this for each transmitter you wish to operate the Unlock/Disarm feature).

(Siren emits 3 short chirps indicating channel 3 has been entered). Within 10 Seconds, Press and hold any unused button(s) of the first transmitter you wish to control Channel 3 output, (Trunk Release) until a long chirp is heard from the siren. Repeat this for each transmitter you wish to operate the Channel 3 output. (Siren emits 4 short chirps indicating channel 4 has been entered).

Within 10 Seconds, Press and hold any unused button(s) of the first transmitter you wish to control Channel 4 output, (Auxiliary Output 1) until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Channel 4 output). (Siren emits 5 short chirps indicating channel 5 has been entered). Within 10 Seconds, Press and hold any unused button(s) of the first transmitter you wish to control Channel 5 output, (Auxiliary Output 2) until a long chirp is heard from the siren.

(Repeat this for each transmitter you wish to operate the Channel 5 output). (Siren emits 6 short chirps indicating channel 6 has been entered). Within 10 Seconds, Press and hold the unlock button, or any unused button(s), of the first transmitter you wish to control Channel 6 output, (Driver Priority 1) until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Channel 6 output, Driver Priority 1).

(Siren emits 7 short chirps indicating channel 7 has been entered). Within 10 Seconds, Press and hold the unlock button or any unused button(s) of the first transmitter you wish to control Channel 7 output, (Driver Priority 2) until a long chirp is heard from the siren.

(Repeat this for each transmitter you wish to operate the Channel 7 output, Driver Priority 2). NOTE: Channels 6 and 7 can be used as a separate output to control a function other than driver priority. Simply programming any unused transmitter button other than the unlock button will allow complete independent control of these outputs.

ERASING TRANSMITTERS IF THEY HAVE BEEN LOST OR STOLEN. NOTE: Before you begin to erase the lost or stolen transmitter(s), have all transmitters available that you wish to remain programmed. These will be used during the program process to identify transmitters that will continue to be used. Enter the transmitter program mode. Within 10 seconds, press and release the valet/program switch three times.

Within 10 Seconds, Press and hold the ARM or ARM/DISARM button of the first transmitter you wish to remain stored into the control unit until a single chirp is heard from the siren. Repeat this for each transmitter you wish to remain stored in the control. The receiver stores up to four transmitters. To be certain all transmitter slots in the receiver are occupied with transmitters you wish to continue to use, and all others are erased, you will have to fill all four receiver slots. If in step 3 you identified one transmitter, you will have to fill the additional 3 slots.

If in step 3 you identified two transmitters, you will have to fill the additional two slots, etc.. Press and hold any unused button or combination of buttons until a long chirp is heard from the siren. Release and press the button or button combination again and again until all remaining slots are full. Repeat this procedure with the appropriate transmitter buttons for all other receiver channels. To reprogram a receiver channel with a different transmitter button once a code has been stored, there will be two options.

Enter the transmitter program mode of the receiver channel to be reprogrammed. Using any unused button or combination of buttons, push out the stored code by pressing the unused button until a long chirp is heard, then repeat 3 additional times. After this, you can add any desired unused transmitter button. This action erases only that particular receiver channel, all other codes will remain stored.

Using any transmitter button press and hold until a long chirp is heard. If a single chirp or multiple chirps, (up to 7 chirps), are heard, the unit is indicating that the transmitter has already been programmed elsewhere in the receiver. Release the transmitter button and within 5 seconds press and hold until a long chirp is heard.

This action forces the unit to erase all stored codes of that transmitter. The unit then exits the program mode the siren emits the program mode exit chirp pattern. All transmitter buttons for that transmitter must now be reprogrammed. Any other transmitter stored in the units memory still remain operational. If the button is released and not pressed again within the 5 second period, no change in programming has been made to the receiver channel.

The programmer can move onto a different channel or erase the transmitter codes as described in 1 above. PLEASE REFER TO YOUR ORIGINAL OWNERS GUIDE FOR YOUR AFTERMARKET INSTALLED KEYLESS ENTRY SYSTEM OR. CONTACT A LOCAL CAR/AUDIO SHOP. How to find out if this remote is compatible with your Vehicles installed RKE System. Check the back of your current or old keyless remote to match FCC ID /Part #s.

Your vehicle will be installed with one of the following keyless entry systems. Standard Keyless Remote Packages: Installed at time of manufacture. Optional Keyless Remote Packages: Installed by a dealer. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. No remote keyless entry system at all. The above information can change which remote you need for your installed remote keyless system. Messages & Best Offers are checked throughout the day & we typically respond 7 days a week. We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Does this keyless remote entry come with a battery? It will have a working battery installed. Installed batteries are not tested for battery life- they are simply working. Some are new and some are used.

The item "Prestige LCD keyless remote car starter transmitter ELVATRBB APS596A AX700 AX900" is in sale since Tuesday, May 21, 2019. This item is in the category "eBay Motors\Parts & Accessories\In-Car Technology, GPS & Security\Dash Cams, Alarms & Security\Remote Entry System Kits".autoparts" and is located in Wellsboro, Pennsylvania. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Montserrat, Turks and caicos islands, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Pakistan, Paraguay, Reunion, Russian federation.


Prestige LCD keyless remote car starter transmitter ELVATRBB APS596A AX700 AX900