M3N65981403 fab keyless remote entry starter Memory 1 clicker control keyfab 11. See pictures for an example of what you will receive. Remote keyless entry fob alarm controller. Transmitter control clicker keyfob controller replacement.
See Item Specifications for more details. 2005 2006 2007 2008 2009 2010 2011. Cadillac STS with remote start. This is a genuine Cadillac remote and will work with the factory remote keyless entry system (RKE) on the cars in the chart above. Your vehicle must have the factory RKE system on it.
Please NOTE: This remote is interchangeable with 15212383. The #1 and #2 remotes look identical. The only difference is the number on the back. Which determines the order that they are programmed.Pre-Owned: An item that has been used previously. The item may have some signs of cosmetic wear, but is fully operational and functions as intended. Scroll through listing for full details and description of any imperfections. Programming the Transmitter to Your RKE System.
There are 4 methods for programming key fobs. Up to 4 key fobs may be programmed to the remote control door lock receiver (RCDLR). Each programmed key fob is given a position of #1-#4 in the RCDLR memory.
Method 1 - Key Fob Quick Learn. This procedure will add key fobs. Fobs will be numbered in sequence based on when they are programmed; if 2 fobs are currently programmed to the RCDLR, a fob programmed using this method will be numbered as Fob 3. This procedure requires that you have a known good key fob, a replacement key fob, and the vehicles mechanical key. Important: This procedure is not available when the maximum number of fobs (4) have been programmed.
If 4 key fobs are programmed to this RCDLR and this method is attempted, the driver information center (DIC) will display MAX FOBS LEARNED and the programming procedure will exit. Method 4 must be used in this instance. The vehicle must be OFF. Place a known key fob within the interior of the vehicle.
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds. The DIC will display a message: READY FOR FOB X (X = fob 2, 3, or 4).
Place the replacement key fob in the console fob pocket with the buttons facing forward. A beep will occur and the DIC will display: READY FOR FOB X (X = fob 3 or 4) or MAX FOBS LEARNED. If programming additional key fobs, repeat steps 5 and 6, or press the OFF/ACC portion of the ignition switch to exit programming mode. Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation. Method 2 - Key Fob Slot Programming.
This procedure will add or replace a key fob. Method 2 allows you to choose which location (slot) the unprogrammed fob will be learned to. If you are replacing a key fob, this method will erase the previously known key fob programmed to that particular slot. This procedure requires that you have a known good key fob, a replacement key fob, the vehicle mechanical key, and a scan tool.If 4 key fobs are programmed to this RCDLR and this method is attempted, the DIC will display MAX FOBS LEARNED and the programming procedure will exit. Use the scan tool, to access the following. Select Fob X (X = 1, 2, 3, or 4) on the scan tool.
This will be the slot you wish to program to. Place the replacement key fob in the console pocket with the buttons facing forward. A beep will occur indicating programming completion.
The previously known fob is now erased. If programming additional key fobs, repeat steps 4-8, or press the OFF/ACC portion of the ignition switch to exit programming.
Method 3 - Key Fob Auto Learn. This procedure will first erase all known key fobs.The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key. Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure.
The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1. Do not place any known good key fobs in the vicinity of the vehicle when programming with Method 3. If the RCDLR recognizes a known good key fob during Method 3 programming, the programming mode will resort to Method 1.
The DIC will display a message: OFF/ACC TO LEARN. Press the OFF/ACC portion of the ignition button. The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time. When the counter reaches 0, DIC will display OFF/ACC TO LEARN.
Repeat steps 5-7 two more times, for a total of 30 minutes. A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2.
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode. If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode.Method 4 - Service Programming System Fob Programming. This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software.
Once the 10-minute timer has expired, the fobs can be programmed similar to Method 2 using slot programming. A scan tool, Techline Terminal, and a replacement key fob are required to perform this procedure. Place the vehicle in the Vehicle On, Engine Off mode. Connect a scan tool to the vehicle. Insure that all power consuming devices are turned OFF on the vehicle.With a scan tool, select Request Info under Service Programming System and follow the scan tool on-screen instructions. Disconnect the scan tool from the vehicle and connect the scan tool to a Techline Terminal with the current Service Programming System (SPS) software. On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions. Ensure the correct programming procedure is selected based on component being replaced or programmed. Disconnect the scan tool from the Techline Terminal and re-connect the scan tool to the vehicle. With a scan tool, select Program ECU under Service Programming System. At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure. When the 10 minute relearn procedure has completed, use the scan tool to access the following. If programming additional key fobs, repeat steps 12-13, or press the OFF/ACC portion of the ignition switch to exit programming. How to find out if this remote is compatible with your Vehicles installed RKE System. If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first. Check the back of your current or old keyless remote to match FCC ID /Part #s. Contact your local dealer and tell them your VIN# and ask what part # / FCC ID you need. Your vehicle will be installed with one of the following keyless entry systems.
Standard Keyless Remote Packages: Installed at time of manufacture. Optional Keyless Remote Packages: Installed by a dealer. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. No remote keyless entry system at all.
The above information can change which remote you need for your installed remote keyless system. Due to scams etc, we DO NOT respond to emails. Messages & Best Offers are checked throughout the day & we typically respond 7 days a week. We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Does this keyless remote entry come with a battery?It will have a working battery installed. Installed batteries are not tested for battery life- they are simply working. Some are new and some are used. Keyless Remote Warehouse is a family-owned company located in North Central Pennsylvania who sells keyless remotes at fractions of dealer prices. We carry almost all OEM factory keyless entry remotes AND aftermarket remotes that work with systems your vehicle may have had installed after they were already manufactured. We pass on our cost savings to you so that you can have the luxury of an affordable keyless remote control for your car, truck, SUV, or minivan. We have survived the ever-changing e-commerce industry modifications by treating our customers as the #1 priority. The simple truth is these items we sell are very complicated, especially for people who do not know a lot about them naturally.
What sets us apart from the other sellers is that we are an American-based company ran by an American-based family. We are reachable for questions and are not a storefront for a China import operation, which seems to be more and more common now-a-days. This listing is currently undergoing maintenance, we apologise for any inconvenience caused. The item "M3N65981403 fab keyless remote entry starter Memory 1 clicker control keyfab 11" is in sale since Wednesday, June 15, 2016. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Safety & Security\Keyless Entry Remotes/Fobs".
The seller is "keyless-remote-warehouse" and is located in Wellsboro, Pennsylvania. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, Sweden, South Korea, Indonesia, Taiwan, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Russian federation, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia.